The car audio business is thriving. New models of car stereos are being released almost monthly, and it's no surprise, being that many people spend a good deal of the day in their vehicle driving to work or running errands. Whether you decide to upgrade your stereo system or have a vehicle with a broken stereo, removing a factory car stereo is relatively easy. Be sure to follow the following steps carefully and the deviation are to be avoided.
This discussion will be helpful for those aspiring to remove the factory car stereo easily without spending too much money and time. For this purpose some tools like screwdriver, quarter inch sockets, and quarter inch socket driver are required. Some steps to remove the factory car stereo are discussed below. They are a set of generalised directions which may be applicable to the car in picture since all cars are different but this definitely gives the reader an idea of how to get the car stereo removed.
The screws that hold the dash plate in place are to be located. Then, the screwdriver
of appropriate size to be used and turned counter clockwise till the screw comes out of the holes. Once the screws are taken out, dash plate is removed and kept aside.
Using a common screw driver remove the cover out. To keep the dash covers on there are snaps that snap into a hole. But if the fuses are on the drivers side then look for the screw which may be inside the cover. The dash cover will be held by these screws. the dash covers are held just by the snaps and screws.
The screws which hold the radio and which is around the face plate is pulled in. and the radio is pulled out so as to remove the electric connector and antenna. The face plate is opened and the right one for your car can be chosen. One should ensure its perfect fitting in the car with the space given.
The new radio has tangs that are provided to keep it in place. The faceplate is first put over the radio and these tangs are bent. Since it is at the rear of the face plate, the radio cannot be pulled. After this is done, the new harness is attached at its respective positions with radio and antennae. The radio is then pushed back to position and screws are fixed to keep the radio in place. The dash cover is then fixed by putting the screws back in its position.
Hence by following the above directions, removing a factory car stereo becomes easy and can be done by any person with enough knowledge of dash covers and connections of stereos.
This discussion will be helpful for those aspiring to remove the factory car stereo easily without spending too much money and time. For this purpose some tools like screwdriver, quarter inch sockets, and quarter inch socket driver are required. Some steps to remove the factory car stereo are discussed below. They are a set of generalised directions which may be applicable to the car in picture since all cars are different but this definitely gives the reader an idea of how to get the car stereo removed.
The screws that hold the dash plate in place are to be located. Then, the screwdriver
of appropriate size to be used and turned counter clockwise till the screw comes out of the holes. Once the screws are taken out, dash plate is removed and kept aside.
Using a common screw driver remove the cover out. To keep the dash covers on there are snaps that snap into a hole. But if the fuses are on the drivers side then look for the screw which may be inside the cover. The dash cover will be held by these screws. the dash covers are held just by the snaps and screws.
The screws which hold the radio and which is around the face plate is pulled in. and the radio is pulled out so as to remove the electric connector and antenna. The face plate is opened and the right one for your car can be chosen. One should ensure its perfect fitting in the car with the space given.
The new radio has tangs that are provided to keep it in place. The faceplate is first put over the radio and these tangs are bent. Since it is at the rear of the face plate, the radio cannot be pulled. After this is done, the new harness is attached at its respective positions with radio and antennae. The radio is then pushed back to position and screws are fixed to keep the radio in place. The dash cover is then fixed by putting the screws back in its position.
Hence by following the above directions, removing a factory car stereo becomes easy and can be done by any person with enough knowledge of dash covers and connections of stereos.
About the Author:
Learn more about Autozubehoer. Stop by Author Name's site where you can find out all about Car stereo and what it can do for you.
No comments:
Post a Comment